2020年に発行されたプラスチックのISO規格 | ||
日本プラスチック工業連盟が原案作成に係わった規格。ISO規格は(一財)日本規格協会より購入できます。 | ||
TC61(プラスチック)関係 期間:2020年12月まで | ||
規格番号 | 標題 | |
ISO 3451-1:2019 | プラスチック−灰分の定量方法−第1部:一般的方法 | |
Plastics -- Determination of ash -- Part 1: General methods | ||
ISO 23153-2:2020 | プラスチック−ポリエーテルエーテルケトン(PEEK)成形および押出材料−第2部:試験片の調製と特性の決定 | |
Plastics -- Polyetheretherketone (PEEK) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties | ||
ISO/TR 21960:2020 | プラスチック−環境側面−知識と方法論の状態 | |
Plastics -- Environmental aspects -- State of knowledge and methodologies | ||
ISO 11357-2:2020 | プラスチック−示差走査熱量測定(DSC)−第2部:ガラス転移温度及びステップ高の測定 | |
Plastics -- Differential scanning calorimetry (DSC) -- Part 2: Determination of glass transition temperature and step height | ||
ISO 19064-2:2020 | プラスチック−スチレン/アクリロニトリル(SAN)成形及び押出材料−第2部:試験片の調製と特性の測定 | |
Plastics -- Styrene-acrylonitrile (SAN) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties | ||
ISO 19066-2:2020 | プラスチック−メタクリル酸メチル・アクリロニトリル・ブタジエン・スチレン成形及び押出材料−第2部:試験片の調製と特性の測定 | |
Plastics -- Methyl methacrylate-acrylonitrile-butadiene-styrene (MABS) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties | ||
ISO 22526-2:2020 | プラスチック−バイオベースプラスチックの炭素及び環境フットプリント−第2部:材料カーボンフットプリント, 空気から除去されてポリマー分子に組み込まれたCO2の量(質量) | |
Plastics -- Carbon and environmental footprint of biobased plastics -- Part 2: Material carbon footprint, amount (mass) of CO2 removed from the air and incorporated into polymer molecule | ||
ISO 22766:2020 | プラスチック−実際の野外条件下での海洋生息地におけるプラスチック材料の崩壊度の測定 | |
Plastics -- Determination of the degree of disintegration of plastic materials in marine habitats under real field conditions | ||
ISO 23153-1:2020 | プラスチック−ポリエーテルエーテルケトン(PEEK)成形及び押出材料−第1部:指定システムと仕様の基礎 | |
Plastics -- Polyetheretherketone (PEEK) moulding and extrusion materials -- Part 1: Designation system and basis for specifications | ||
ISO 20819-1:2020 | プラスチック−木材・プラスチック再生複合材(WPRC)−第1部:仕様 | |
Plastics -- Wood-plastic recycled composites (WPRC) -- Part 1: Specification | ||
ISO 22403:2020 | プラスチック−中温性好気性実験室条件下で海洋接種に曝露された材料の固有の生分解性の評価−試験方法及び要求事項 | |
Plastics -- Assessment of the intrinsic biodegradability of materials exposed to marine inocula under mesophilic aerobic laboratory conditions -- Test methods and requirements | ||
ISO 26723:2020 | プラスチック−全視感透過率と反射率の測定 | |
Plastics -- Determination of total luminous transmittance and reflectance | ||
ISO 179-2:2020 | プラスチック−シャルピー衝撃特性の測定−第2部:計装衝撃試験 | |
Plastics -- Determination of Charpy impact properties -- Part 2: Instrumented impact test | ||
ISO 24022-2:2020 | プラスチック−ポリスチレン(PS)成形及び押出し材料−第2部:試験片の調製及び特性の決定 | |
Plastics -- Polystyrene (PS) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties | ||
ISO 24023-1:2020 | プラスチック−軟質ぼり塩化ビニール(PVC-P)成形及び押出成形材−第1部:指定システム及び仕様の基礎 | |
Plastics -- Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials -- Part 1: Designation system and basis for specifications | ||
ISO 24023-2:2020 | プラスチック−軟質ぼり塩化ビニール(PVC-P)成形及び押出成形材−第2部:試験片の調製及び特性の測定 | |
Plastics -- Plasticized poly(vinyl chloride) (PVC-P) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties | ||
ISO 24025-1:2020 | プラスチック−スルホンポリマー成形及び押出材料−第1部:指定システム及び仕様の基礎 | |
Plastics -- Sulfone polymer moulding and extrusion materials -- Part 1: Designation system and basis for specifications | ||
ISO 24025-2:2020 | プラスチック−スルホンポリマー成形及び押出材料−第2部:試験片の調製及び特性の測定 | |
Plastics -- Sulfone polymer moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties | ||
ISO 24026-1:2020 | プラスチック−ポリ(メチルメタクリレート)(PMMA)成形及び押出材料−第1部:仕様システム及び仕様の基礎 | |
Plastics -- Poly(methyl methacrylate) (PMMA) moulding and extrusion materials -- Part 1: Designation system and basis for specifications | ||
ISO 24026-2:2020 | プラスチック−ポリ(メチルメタクリレート)(PMMA)成形材料及び押出材料−第2部:試験片の調製及び特性の決定 | |
Plastics -- Poly(methyl methacrylate) (PMMA) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties | ||
ISO 26842-1:2020 | 接着剤−室内木製品用接着剤の評価及び選択のための試験方法−第1部:厳しくない環境における層間はく離耐性 | |
Adhesives -- Test methods for the evaluation and selection of adhesives for indoor wood products -- Part 1: Resistance to delamination in non-severe environments | ||
ISO 26842-2:2020 | 接着剤−室内木製品用接着剤の評価及び選択のための試験方法−第2部:厳しい環境における層間はく離耐性 | |
Adhesives -- Test methods for the evaluation and selection of adhesives for indoor wood products -- Part 2: Resistance to delamination in severe environments | ||
ISO 294-3:2020 | プラスチック−熱可塑性材料試験片の射出成形−第3部:小プレート | |
Plastics -- Injection moulding of test specimens of thermoplastic materials -- Part 3: Small plates | ||
ISO 1628-2:2020 | プラスチック−毛細管粘度計による薄い溶液でのポリマーの粘度の測定−第2部:ポリ塩化ビニル樹脂 | |
Plastics -- Determination of the viscosity of polymers in dilute solution using capillary viscometers -- Part 2: Poly(vinyl chloride) resins | ||
ISO 10119:2020 | 炭素繊維−密度の測定 | |
Carbon fibre -- Determination of density | ||
ISO 19679:2020 | プラスチック−海水/堆積物界面の非浮遊プラスチック材料の好気的生分解度の求め方−発生二酸化炭素の分析による方法 | |
Plastics -- Determination of aerobic biodegradation of non-floating plastic materials in a seawater/sediment interface -- Method by analysis of evolved carbon dioxide | ||
ISO/TS 21488:2020 | プラスチック−自然風化と人工照射を組み合わせた屋外でのポリオレフィンの暴露試験方法 | |
Plastics -- Test method for exposing polyolefins outdoors combining natural weathering and artificial irradiation | ||
ISO 10350-2:2020 | プラスチック−比較可能シングルポイントデータの取得及び表示−第2部:長繊維強化プラスチック | |
Plastics -- Acquisition and presentation of comparable single-point data -- Part 2: Long-fibre-reinforced plastics | ||
ISO 10352:2020 | 繊維強化プラスチック−成形材料及びプリプレグ−単位面積あたりの質量と単位面積あたりの繊維質量の求め方 | |
Fibre-reinforced plastics -- Moulding compounds and prepregs -- Determination of mass per unit area and fibre mass per unit area | ||
ISO 19063-2:2020 | プラスチック−耐衝撃性ポリスチレン(PS-I)成形及び押出材料−第2部:試験片の準備と特性の求め方 | |
Plastics -- Impact-resistant polystyrene (PS-I) moulding and extrusion materials -- Part 2: Preparation of test specimens and determination of properties | ||
ISO 22526-3:2020 | プラスチック−バイオベースプラスチックの炭素及び環境フットプリント−第3部:カーボンフットプリントの処理,定量化の要求事項及びガイドライン | |
Plastics -- Carbon and environmental footprint of biobased plastics -- Part 3: Process carbon footprint, requirements and guidelines for quantification | ||
ISO 23706:2020 | プラスチック−標準的な耐候性試験方法における特性変化の見かけの活性化エネルギーの決定 | |
Plastics -- Determination of apparent activation energies of property changes in standard weathering test methods | ||
ISO 24022-1:2020 | プラスチック−ポリスチレン(PS)成形及び押出し材料−第1部:仕様体系と仕様の根拠 | |
Plastics -- Polystyrene (PS) moulding and extrusion materials -- Part 1: Designation system and basis for specifications | ||
ISO 19935-2:2020 | プラスチック−温度調節されたDSC−第2部:比熱容量cpの測定 | |
Plastics -- Temperature modulated DSC -- Part 2: Measurement of specific heat capacity cp | ||
ISO 20329:2020 | プラスチック−往復直線スライド運動による摩耗の測定 | |
Plastics -- Determination of abrasive wear by reciprocating linear sliding motion | ||
ISO 22836:2020 | 繊維強化複合材料−密閉圧力容器を使用した水分吸収の促進と水分による過飽和コンディショニングの方法 | |
Fibre-reinforced composites -- Method for accelerated moisture absorption and supersaturated conditioning by moisture using sealed pressure vessel | ||
ISO/TR 23891:2020 | プラスチック−リサイクルと回収−基準の必要性 | |
Plastics -- Recycling and recovery -- Necessity of standards | ||
ISO 23977-1:2020 | プラスチック−海水にさらされたプラスチック材料の好気性生物分解の測定−第1部:発生した二酸化炭素の分析による方法 | |
Plastics -- Determination of the aerobic biodegradation of plastic materials exposed to seawater -- Part 1: Method by analysis of evolved carbon dioxide | ||
ISO 23977-2:2020 | プラスチック−海水にさらされたプラスチック材料の好気性生物分解の測定−第2部:密閉呼吸計で酸素要求量を測定する方法 | |
Plastics -- Determination of the aerobic biodegradation of plastic materials exposed to seawater -- Part 2: Method by measuring the oxygen demand in closed respirometer | ||
ISO 9772:2020 | 発泡プラスチック−小火炎を受ける小型試料の水平燃焼の測定 | |
Cellular plastics -- Determination of horizontal burning characteristics of small specimens subjected to a small flame | ||
ISO 10093:2020 (12月発行) |
プラスチック−引火試験−標準発火源 | |
Plastics -- Fire tests -- Standard ignition sources | ||
ISO 22838:2020 (12月発行) |
複合材料と強化繊維−ダブルカンチレバービーム試験片を使用した炭素繊維強化プラスチック(CFRP)と金属の結合プレートの破壊エネルギーの決定 | |
Composites and reinforcements fibres -- Determination of the fracture energy of bonded plates of carbon fibre reinforced plastics (CFRPs) and metal using double cantilever beam specimens | ||
TC138(流体輸送用プラスチック管、継手及びバルブ類)関係 期間:2020年12月まで | ||
規格番号 | 標題 | |
ISO 11296-7:2019 | 非加圧地下排水及び下水網の修復用プラスチック配管システム−第7部:らせん巻管によるライニング | |
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks -- Part 7: Lining with spirally-wound pipes | ||
ISO 21138-1:2020 | 非加圧地下排水及び下水用のプラスチック配管システム−非可塑性ポリ塩化ビニル(PVC-U),プロプロピレン(PP)及びポリエチレン(PE)の構造壁配管システム−第1部:材料仕様及び性能基準 | |
Plastics piping systems for non-pressure underground drainage and sewerage -- Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -- Part 1: Material specification and performance criteria for pipes, fittings and systems | ||
ISO 21138-2:2020 | 非加圧地下排水及び下水用のプラスチック配管システム−非可塑性ポリ塩化ビニル(PVC-U),プロプロピレン(PP)及びポリエチレン(PE)の構造壁配管システム−第2部:滑らかな外面をもつ管及び管継手,タイプA | |
Plastics piping systems for non-pressure underground drainage and sewerage -- Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -- Part 2: Pipes and fittings with smooth external surface, Type A | ||
ISO 21138-3:2020 | 非加圧地下排水及び下水用のプラスチック配管システム−非可塑性ポリ塩化ビニル(PVC-U),プロプロピレン(PP)及びポリエチレン(PE)の構造壁配管システム−第3部:滑らかでない外面をもつ管及び管継手,タイプB | |
Plastics piping systems for non-pressure underground drainage and sewerage -- Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and polyethylene (PE) -- Part 3: Pipes and fittings with non-smooth external surface, Type B | ||
ISO 8659:2020 | 熱可塑性プラスチック弁−疲れ強さ−試験方法 | |
Thermoplastics valves -- Fatigue strength -- Test method | ||
ISO 13954:1997/Amd 1:2020 | 修正票1−プラスチック管及び管継手−90 mm以上の呼び外径のポリエチレン(PE)電気溶解アセンブリの引き剥がし試験 | |
Plastics pipes and fittings -- Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm | ||
ISO 13955:1997/Amd 1:2020 | 修正票1−プラスチック管及び管継手−ポリエチレン(PE)電気溶解アセンブリの破砕試験 | |
Plastics pipes and fittings -- Crushing decohesion test for polyethylene (PE) electrofusion assemblies | ||
ISO 8521:2020 | ガラス強化熱硬化プラスチック(GRP)管−見掛けの初期周方向強さの測定のための試験方法 | |
Glass-reinforced thermosetting plastic (GRP) pipes -- Test methods for the determination of the initial circumferential tensile wall strength | ||
ISO 13259:2020 | 地下の非圧力用途の熱可塑性配管システム−エラストマーシールタイプ継手の漏れ耐性の試験方法 | |
Thermoplastics piping systems for underground non-pressure applications -- Test method for leaktightness of elastomeric sealing ring type joints | ||
ISO 8779:2020 | プラスチック配管システム−かんがい用ポリエチレン(PE)管−仕様 | |
Plastics piping systems -- Polyethylene (PE) pipes for irrigation -- Specifications | ||
ISO 16486-1:2020 | ガス燃料供給用プラスチック配管システム−融着接合及び機械接合をもつ硬質ポリアミド(PA-U)配管システム−第1部:一般 | |
Plastics piping systems for the supply of gaseous fuels -- Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing -- Part 1: General | ||
ISO 6259-2:2020 | 熱可塑性管−引張特性の測定方法−第2部:無可塑ポリ塩化ビニール(PVC-U),塩素化ポリ塩化ビニール(PVC-C)及び高耐力ポリ塩化ビニール管 | |
Thermoplastics pipes -- Determination of tensile properties -- Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), oriented unplasticized poly(vinyl chloride) (PVC-O), chlorinated poly(vinyl chloride) (PVC-C) and high-impact poly(vinyl chloride) (PVC-HI) | ||
ISO 16486-2:2020 | ガス燃料供給用プラスチック配管システム−融着接合及び機械接合をもつ硬質ポリアミド(PA-U)配管システム−第2部:管 | |
Plastics piping systems for the supply of gaseous fuels -- Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing -- Part 2: Pipes | ||
ISO 16486-3:2020 | ガス燃料供給用プラスチック配管システム−融着接合及び機械接合をもつ硬質ポリアミド(PA-U)配管システム−第3部:管継手 | |
Plastics piping systems for the supply of gaseous fuels -- Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing -- Part 3: Fittings | ||
ISO 15494:2015/Amd 1:2020 | ||
ISO 15494:2015/追補1:2020 | ||
ISO 15875-2:2003/Amd 2:2020 | ||
ISO 15875-2:2003/追補2:2020 | ||
ISO 22391-2:2009/Amd 1:2020 | ||
ISO 22391-2:2009/追補1:2020 | ||
ISO 15877-5:2009/Amd 2:2020 | ||
ISO 15877-5:2009/追補2:2020 | ||
(12月発行) | ISO 15875-3:2003/Amd 1:2020 | |
ISO 15875-3:2003/追補1:2020 | ||
(12月発行) | ISO 15875-5:2003/Amd 1:2020 | |
ISO 15875-5:2003/Amd 1:2020 | ||
(12月発行) | ISO 15876-2:2017/Amd 1:2020 | |
ISO 15876-2:2017/追補1:2020 | ||
(12月発行) | ISO 15876-3:2017/Amd 1:2020 | |
ISO 15876-3:2017/追補1:2020 | ||
(12月発行) | ISO 15876-5:2017/Amd 1:2020 | |
ISO 15876-5:2017/追補1:2020 | ||
(12月発行) | ISO 15877-2:2009/Amd 2:2020 | |
ISO 15877-2:2009/追補2:2020 | ||
(12月発行) | ISO 22391-3:2009/Amd 1:2020 | |
ISO 22391-3:2009/追補1:2020 | ||
(12月発行) | ISO 22391-5:2009/Amd 1:2020 | |
ISO 22391-5:2009/追補1:2020 |